PlasterMax™ the only code approved drywall replacement over ICF.

Recycled Green building material that is abuse and mold resistant by Gigacrete™

PlasterMax StaircasePlasterMax - Worlds first fire rated sustainable, abuse resistant interior veneer plaster specifically formulated for EPS foam but can also be applied over EPS form, CMU, drywall, and concrete blocks. PlasterMax offers unparalleled abrasion resistance, fire rating performance, healthy indoor air quality and environmental sustainability.

Composites do not shrink or crack like concrete and are hurricane, earthquake/water/mold resistant all made with recycled materials. Whether you are seeking a coating with leading Green performance requirements for ICF, looking for greater abrasions resistant surfaces for hospitals/schools etc, looking for less maintenance, eliminate mold/mildew issues, trying to reduce labor and installation times, or a designer seeking sustainable materials, GigaCrete products fit the bill.

PlasterMaxPerformance Benefits.

  • Single coat applications from 1/8"- ¼" (1/8" replaces ½ gypsum board
  • Provides tough protective finish over ICF/SIP's
  • Impact Resistance (ASTM C1629)
  • High Performance resistance (ASTM D4977)
  • Zero flame spread and smoke developed (ASTM 84)
  • Non combustible building material (ASTM E136)
  • Smooth or textured finishes- accepts paint
  • Applied by conventional spray pumps or hawk and trowel
  • Exceeds EPA and CA indoor air quality & VOC standards (AQS, Report # 157763)
  • Environmentally sustainable without the addition of crystalline silica
  • Mold and mildew resistant (ASTM G 21)
  • Eliminates difficult drywall applications on ceilings
  • Suitable as final fire barrier coating for wall areas above ceiling grids
  • Resistant to fire, moisture, insect, vermin, mold and mildew
  • A sustainable "Green" product.
  • Minimum 6,000 PSI compressive strength, (ASTMC109)
  • Meets all emission level requirements of GreenGuard Report # 15995-06
  • Recognized by LEED and US Green Building Council for points

PlasterMax for applications over EPS foam to replace Gypsum board with a fire rated abuse resistant barrier

PlasterMax replacing Gypsum Board

GigaCrete building products are NON COMBUSTIBLE

While the PlasterMax interior veneer plaster system provides the ultimate in finishing of ICF construction, its application over EPS insulation sheets, energineered panesl such as cement or fiberboard, monolithic concrete and unit masonry, offers unique advantages to these conventional all systems as well. Important product performance features include: superior fire resistance, 0 flame spread and 0 smoke developed, no VOC emissions, extreme abrasion and improved indent resistance superior to abuse resistant gypsum board and high resistance to mold and mildew.

The new concrete matrix does not use Portland cement, sand or gravel but instead a proprietarty nontoxic polymer binder. Additional fillers include waste paper, cardboard, plastics, Styrofoam packaging, recycled glass, sludge from paper mills and agricultural waste fibers. The recycled materials are mixed with GigaCrete's own mineral cement formulation, which requires less water and yields less carbon dioxide in production than cement. Most of these materials would end up in a landfill instead they make a great alternative Green Building Product. It is mixed like concrete with dry ingredients but with very little water. Normal concrete requires up to 28 days for adequate curing but GigaCrete products sets solid in 4 hours and is usable in 8 hours. It is less expensive building solution due to the speed of construction and therefore labor savings.

GigaCrete Products are Green

No other product has all the benefits of GigaCrete's PlasterMax and BallistiCrete

GigaCrete Products are Green

PlasterMax over EPS foam to replace Gypsum board with a fire rated abuse resistant barrier

  • Eliminate cutting around outlets, ducts, trusses, sprinkler lines, conduits.
  • Eliminate sound transmitting steel screws.
  • Eliminate taping joints, drywall compound and repeated dusty sanding.
  • Eliminate repairing holes by cutting out drywall and repeated taping and sanding again.
  • PlasterMax can be sprayed directly over ICF/SIP's panels and patched with the same 1 coat of paint covers.
  • PlasterMax will not support mold or mildew.

GONE ARE THE DRAWBACKS OF DRYWALL!!!

Gone are mudding and taping and easily dented and scratched walls

Faster and simpler, less labor, less cost.

PACKAGING

PlasterMax Bags are 75lbs 2 part products come pre-mixed. Add part B and mix with plaster mixers


AVERAGE COVERAGE

( Thickness of coating)
1/8" = 53.25 SQ Feet per bag
3/16" = 35.5 SQ Feet per bag
¼ = 26 SQ Feet per bag

Applies over ICF/SIP's EPS Foam, CMU, concrete or gyp board, requires a 4.5 oz or heavier Fiberglass mesh typical to EIFS finishes

More info

Surface Abrasion Comparative Data (Metric)
Impact Resistant of Various Interior Claddings for ICF System
Gigacrete products PlasterMax economics

 

Product Catalogue

 

 

 

We have offices on Amelia Island, Florida and in Sandy Point, Maine and ship nationwide, factory direct. We are a Women Owned Businesses (WOBs), Service Disabled Veteran Owned Businesses (SDVOBs), Central Contractor Registered Business, members of NHBA, NEFBA, and Florida Green Building Coalition. Retired after 28 years in Air National Guard.




Connect with Barrett Enterprises TODAY - and learn more about our great products and offers!

Facebook  Linked In  Twitter  Greenbuilding Blog 
Youtube  Email  Evernote  Pinterest 
Send us an email for great deals TODAY!

Sustainable Eco Building

Read our new blog about green building materials, energy saving and more! Read more »

Product Showcase

Crete Heat Solex Reflective Insulation


Contact information

Barrett Enterprises Inc.
PO Box 18, Sandy Point, ME 04972
PO Box 15727, Amelia Island, FL 32035
E-mail: info@barrett-inc.com
Tel.: 1-877-904-8424
Fax.: 1-877-513-4203
MainePages.com